Used Mills For Sale
Ball Mills, Hammermills, Roll Mills, SAG Mills & more
In Stock & Ready To Ship

13' diameter x 21' long ball mill, manufactured by Allis Chalmers Svedala, rubber-lined mill, with Siemens-Allis 2,000 HP, 4000 volt, 200 RPM synchronous motor, Eaton airflex clutch. Includes trommel discharge, ball mill rejects conveyor, lube system, etc. Offered complete with controls. New in 1979. Completely rebuilt in 1998, serial number C-2485. Previously used at phosphate minerals processing facility. Also available pumps, spare parts, drives, controls to comprise of complete mill system. Equipment was dismantled and is now being stored at crane yard for easy loading.





Ferrell-Ross Two High Roll Mill, Model 12x52 2-HI RH, Serial number 7829. Features (4) corrugated 12" x 52" rolls, chilled cast iron construction, fitted with forged steel shafts, with double row self-aligning SKF spherical roller bearings, heavy duty mild steel mill housing, safety guards, springs with positive roll stops, lever style cam roll adjustment. Complete with V-belt drive and pedestal with adjustable motor base, product sampling doors and aspiration ports. Mill is driven by 75 HP Baldor electric motor, 230/460 V, 3-phase, 60 Hz, with adjustable motor base mounted to motor stand. Unit includes top-mounting feed hopper. Previously ran for 100 hours only and in very good condition.







Hammermill, manufactured by American Pulverizer. Model WC-30-UR-NF, Serial number 8817. Four-armed design, complete with reversible swing-type stirrup hammers, 1045 heat-treated steel hammer shafts, heavy-duty ball bearings, replaceable liners constructed of abrasion-resistant steel and cast manganese, T-1 adjustable breaker plate, non-clogging bottom housing, front and rear inspection doors, discharge ares with 1/16" perforated screen plates. Infeed section measures 32" wide x 14". Mill is driven by 75 HP, 1800 RPM TEFC motor, 3-phase, 60 Hz, 230/460 Volt. Unit is unused, never installed.







11.5' diameter X 17' long ball mill, manufactured by KVS (Kennedy Van Saun), includes 1000 HP open winding synchronous motor. Features trommel discharge and feed tank. Refurbished in 2013, which included installation of new oil jacking system, oil lube system for Babbitt bearings, new titanium steel water jet-machined discharge grates, and motor refurbishment. Set of new babbit bearings available. Previously operated as a closed circuit dry mill with grinding capacity of 40 metric tons per hour with output fineness of >80% passing 200 mesh. Motor operating speed of 15.8 RPM charged with approximately 78 tons of 1", 2" and 3" steel balls. Last used at a phosphate processing facility and in good condition.






5' diameter X 6' long ball mill, manufactured by Patterson Industries, Type D, non-jacketed, with AR400 steel liners. Includes 30 HP, 3 phase, 60 Hz, 230-460 V, 1725 RPM motor. Mill drive is integrally coupled to horizontal parallel shafted helical gear reducer. Continuous type, with product feeding through spiral inlet trunnion and exiting through the discharge end trunnion. Features cylinder manway access door for cleaning. Internal volume measures approximately 839 USG (112 CF). Mill shell is lined with (24) 1/4" thick liner plates, each head lined with (8) 3/8" thick pie-shaped liner plates. Mounted on stand with approximately 66" clearance between the mill cylinder and floor. Mill was intended for use in glass particle size reduction but were never installed. Manufactured in 2019, unit is still in factory plastic wrap and in new condition.






45" diameter x 48" long ball mill, manufactured by Paul O. Abbe Ball Mill, Model 4-A, rated for 330 Gallon capacity, 44 cubic feet. Previously used as dry grind mill to process precious metal scrap into a 70 mesh material. Last used with timer control panels so that the units would operate for a specific cycle time and then automatically shut off to optimize the cycle time. Mounted on frame. Mill was well maintained and in good working order when removed from service in 2020. Includes ball charge.