Issue 40

March 26, 2026

Time to Read: 5 Minutes


-Hot Take-

Culture beats wages in the long run. A toxic shop can pay top dollar and still lose its best talent.

Joke of the Week

Knock knock

Who's there?

ITAR

ITAR who?

Sorry, I can't tell you that.

Ask a CAM Pro

Real shop problems. Answers from people who have been there.

How can I program to improve surface finish on contouring?


Surface finish on contouring is one of those details that separates good parts from great ones. You can hit every tolerance and still end up with chatter marks, washboarding, or swirl lines that ruin the look and feel. Getting a better finish comes down to controlling tool pressure, motion, and consistency from start to finish.


Start with the right tool.

Choose a cutter with proper geometry for finishing, such as sharp edges, high helix angles, and polished flutes for aluminum. Make sure the tool is balanced and in good condition. A dull edge or chipped corner will show up immediately on a contoured surface.


Keep tool pressure consistent.

Program your lead-in and lead-out moves so the tool engages smoothly and exits without deflection. Avoid plunging straight into the wall. Use tangent or arc entries and match your entry and exit angles to keep the cut stable the whole way through.


Use climb milling whenever possible.

Climb milling gives a cleaner surface and less rubbing because the cutter starts thick and exits thin. It keeps the cutting forces more predictable and prevents the tool from pushing material instead of slicing it.


Tighten your stepovers and overlap passes.

Smaller stepovers and overlapping passes reduce cusp height and blend tool marks. A stepover between five and ten percent of the tool diameter usually gives a good finish without adding too much cycle time. Use constant scallop or constant step paths for uniform marks.


Adjust feed and speed for harmony, not aggression.

A smooth finish comes from balance, not brute force. If you see vibration or waviness, slightly lower the feed or raise the RPM to find the sweet spot. Listen to the cut. A steady hum means stability; a rattle means deflection or pull.


Fine-tune your tolerance and smoothing settings.

Loose tolerances or heavy smoothing can create visible transitions or flat spots. Match your tolerance to the surface requirement. Tighten only as much as needed, since overly small values can slow the machine buffer and extend cycle time unnecessarily.


Keep your finishing tools sharp.

Never finish with a tool that’s already done roughing. Even minor wear will dull your shine. Use a dedicated finisher and take a light, consistent pass of about five to ten thousandths on the wall.


Prepare even stock for finishing.

A semi-finish pass before your final cut removes leftover variations and ensures the finishing tool sees a uniform load. Skipping that step is the easiest way to end up with inconsistent surfaces.


Bottom line:

A clean finish is all about consistency. Keep the engagement steady, the tool sharp, and the motion smooth, and every contour will come out looking intentional..


Have a programming question?


Send it in for the next edition of Ask a CAM Pro!

Weekly Poll

Choose from the answers below.

(Keep scrolling to see last week's poll results.)

How does your shop handle rush jobs from customers?

View the results of last week's poll HERE.

From the Floor


The Great Gatorade Coolant Prank


"We once had someone swap all the machine coolant with blue Gatorade for April Fools. Two hours of confusion, lots of bad words, and a sticky mess later, everybody finally clocked what happened.


Leadership gave the prankster a 'blunt teaching moment.' Still, nobody laughed as hard as the guy who came in early for his shift and discovered all the tanks full of sports drink. He swore off April Fools

pranks from that day on. Nobody blamed him."


– Machinist

Video of the Week (Powered by GibbsCAM)

Video Demo: GibbsCAM Full Mill Demo, 2 through 5 Axis

See how GibbsCAM takes a part from setup to finished code, including solid model creation, 3-axis machining, Hole Manager, VoluMill roughing, 3D surfacing, 4-axis positioning, 5-axis machining, simulation, and post processing.

CAMedy Central

Industry Intel

Musk Says Tesla, SpaceX to Build Advanced Chip Manufacturing Facility - Elon Musk announced plans to build "Terafab," a dual chip manufacturing facility in Austin, Texas, to produce specialized AI chips for Tesla's EVs and Optimus robots as well as SpaceX's space-based data centers, citing future demand that he claims will eventually exceed total global chip output.



13 North American Packaging Manufacturers Announce Expansions - More than a dozen North American packaging companies, including ePac, Cascades, Rand-Whitney, and International Paper, recently announced facility expansions spanning corrugated boxes, flexible packaging, and digital printing as companies invest in new plants and upgraded capacity across the U.S., Canada, and Mexico.


Additive and Subtractive on the Same Machine - Phillips Corporation is showcasing a retrofit system for standard Haas machines that allows shops to switch between additive and subtractive manufacturing within the same program, making hybrid machining more accessible to shops without requiring new equipment.


Industry Growth (Open Jobs)

A few hot openings across the industry this week:



CNC Milling Programmer/Machinist (2nd shift) - Mountain Manufacturing - Lino Lakes, MN


CNC Lead Programmer - Lapham-Hickey Steel - St. Paul, MN


Nightshift Machinist - Rosenboom Machine & Tool Inc - Spirit Lake, IA


CNC Machinist - Dynamic Engineering - Big Stone City, SD


Precision Machining Instructor - ND State College of Science - Wahpeton, ND


CNC Programmer - New Age Manufacturing - Plattsmouth, NE


CNC Programmer - Icon Design LLC - Hazelwood, MO



CNC Programmer - Wichita Machine Products - Wichita, KS

Trade Show & Event Radar

Date

Show

Location

April 8-9

2MTEC

Albert Lea, MN

April 13-16

Machining Summit on the Summit

Mammoth Lakes, CA

April 13-16

Modex26

Atlanta, GA

April 22-23, 2026

MD&M South

Charlotte, NC

May 6-7

Morris & Tsugami America Open House

Brooklyn Park, MN

June 22-25

Automate

Chicago, IL

July 29-30

Advanced Manufacturing Expo

Grand Rapids, MI

Sept 14-19, 2026

IMTS

Chicago, IL

Did someone forward you this newsletter?

Subscribe to get your own copy every week.