To view this email as a web page, click here.

Flying the Zenith CH 750 Super Cruzer

Ride along with Zenith Aircraft demo pilot Roger Dubbert as he takes Brenda flying in the Zenith CH 750 Super Cruzer. The prototype airplane was introduced at Oshkosh AirVenture earlier this year, where Brenda and her husband Brad (from Tennessee) ordered their CH 750 Super Cruzer kit. They participated at the most recent Zenith hands-on workshop class at the Zenith factory, where they went flying in the Super Cruzer as part of the workshop experience. They built their rudder tail section as part of the workshop class, and trailered home the rest of the CH 750 Super Cruzer kit.

Zenith Aircraft's newest design has been optimized to take full advantage of the FAA's new MOSIAC rule. The all-metal, high-wing kit airplane brings together cross-country cruising and sport utility in a roomy, all-metal kit airplane. Combining the payload capability of the STOL CH 750 Super Duty with the cruising focus of the CH 750 Cruzer, it features a redesigned wing leading edge and updated tail for speed, along with a spacious cabin and versatile two-plus-one seating with a rear jump seat. Enjoy outstanding visibility and ample room for people and gear to make every flight an adventure.

Of course, building your own airplane is part of the adventure, and the CH 750 Super Cruzer makes that goal approachable with Zenith’s modern, final-hole-size match-drilled kit technology. Designed for straightforward assembly, it gives first-time and experienced builders alike the satisfaction of creating an airplane they can fly, maintain, and truly call their own. Check out the video (below) as Zenith Aircraft's Sebastien Heintz goes flying in the Zenith CH 750 Super Cruzer:

The prototype Zenith is powered by a stock 180-hp Lycoming O-360 turning a three-blade, ground-adjustable Sensenich propeller. Initial testing produced cruise speeds above 120 mph, while VNE is listed at 160 mph. Zenith is adding fairings (especially wheel fairings) and experimenting with different propellers to maximize cruise capability of the new design. The prototype test airplane features a 50-inch-wide cabin with large bubble doors and a center-mounted Garmin G3X display console.
As a kit (amateur-built experimental) aircraft, the builder chooses the engine and avionics to install, and can optimize the CH 750 Super Cruzer for speed (small wheels and fairings, cruise propeller pitch) or backcountry utility (larger wheels and tires, climb prop).

Build It. Fly It. With Zenith Aircraft

Later next week, Zenith is providing two separate opportunities for you to get started building your own Zenith kit airplane!

The next factory workshop is scheduled for October 8th and 9th in Mexico, Missouri, giving participants the opportunity to learn all about building their own Zenith kit while visiting the factory and staff where the aircraft are produced.
If you've always dreamed of building your own airplane, or simply want to learn more about all-metal aircraft construction, Zenith Aircraft Company is providing you with the opportunity to learn all about building a Zenith kit airplane at one of its factory workshops. The workshops are coordinated by Zenith Aircraft staff and held right in the factory. Small group sizes make the workshops very productive and educational.

During the educational workshop you start building your own Zenith kit aircraft (the rudder tail section of the low-wing Zenith CH 650 or high-wing CH 750 series). Come prepared to work and experience first-hand how you can build your own kit airplane! You don't need any experience, skills or tools to attend. Participating at the factory workshop makes an excellent getaway for you, your spouse or a friend! Spend a couple of days at the Zenith Aircraft factory and meet with fellow aviation enthusiasts - all while gaining valuable hands-on building skills. The demo flight is part of the factory workshop experience, as is a guided factory tour!

Zenith Workshop in Michigan

Also next week, on October 9 and 10, Zenith will return to Howell, Michigan, for its second consecutive year of offering a two-day kit-building workshop there. Participants will build a complete rudder tail section from a standard Zenith kit while learning skills including reading drawings, drilling and blind riveting. The Michigan event is being organized with local builder and EAA Chapter 1056 member Steve Aupperle, with support from Martina and Oliver Reik of Midwest Flying Machines. An informal Zenith fly-in at Livingston County Airport is planned following the workshop. Enthusiasts and current flyers/builders are invited to fly or drive in. Zenith staff will be driving their “Zenith Sprinter cargo van” to Michigan for the workshop, and will be available to deliver kits and parts along the way (with prior arrangement).

Attending Zenith Aircraft’s famous hands-on workshop class is the easiest way to get started on your very own airplane! Plan now to join us at the October workshop class in Michigan or the workshop class at the Zenith factory.

 
Email  Facebook  Instagram  LinkedIn  Web  X  YouTube