Issue 46

May 7, 2026

Time to Read: 6 minutes


-Hot Take-

You can teach someone how to run a machine, but you can't teach them how to care if they don't give a damn.

Joke of the Week

Q: What's the difference between a good setup and a miracle?

A: A miracle doesn't require three guys standing around saying, "Try it now!"

Ask a CAM Pro

Real shop problems. Answers from people who have been there.

How should I adjust my program when cutting Inconel?


Inconel isn’t your everyday material. It’s tough, abrasive, and holds heat like it’s trying to destroy your tooling on purpose. If you program it like mild steel or aluminum, you’ll get short tool life, chatter, and burned edges in no time. The key is managing heat, pressure, and engagement.


Start with the right tools.

Run sharp, positive-geometry carbide with heat-resistant coatings like AlTiN or Inconel-specific grades. Skip uncoated cutters and generic end mills; they’ll dull instantly. For drilling, use solid carbide or cobalt drills with through-coolant if you have it.


Cut slow and steady.

Inconel loves low surface speed and steady feed. Start around 20–40 SFM for milling and 10–30 SFM for drilling, depending on the tool. Keep chip load consistent; too light and you rub, too heavy and you snap the edge. Find the balance where chips are coming off dark straw color, not glowing.


Use climb milling and constant engagement.

Climb milling reduces work hardening and tool rubbing, while adaptive or high-efficiency toolpaths spread the load evenly. Keep radial engagement under 20 percent when roughing and go deep axially to use the full flute length.


Flood it with coolant.

Inconel builds heat fast and dumps it into the tool instead of the chip. Use high-pressure, high-volume coolant right at the cut. Through-tool coolant is ideal. Air blast alone won’t cut it for heavy milling.


Watch your stepovers and stepdowns.

Small radial stepovers with moderate axial depths work best. The goal is to maintain steady contact and avoid re-cutting chips, which are harder than the material itself. Keep your tool engaged, but not buried.


Use rest machining to your advantage.

Rough with stronger tools, then come back with a fresh cutter for semi and finish passes. Don’t make a finishing tool do roughing work; it’ll dull before it ever touches final surfaces.


Inspect your tools often.

Edge wear happens fast. Look for flank wear or micro-chipping and replace tools before they fail. Tool life management in Inconel is about consistency, not endurance.


Bottom line:

Inconel punishes impatience. Stay cool, stay consistent, and let the tool cut, not rub, and the part will come out clean every time.


Have a programming question?


Send it in for the next edition of Ask a CAM Pro!

Weekly Poll

Choose from the answers below.

(Keep scrolling to see last week's poll results.)

What do you wish customers understood better about precision machining?

View the results of last week's poll HERE.

From the Floor

Not the Intern's Fault (But Don't Tell the Boss...)


"I once spent two hours chasing a mystery Z-axis problem.


I checked the code.

I checked the setup.

I checked the fixturing.

I checked everything I could think of.

And, for a brief moment, I was feeling pretty good about blaming the new intern.


There was just one problem.

The intern had quit the week before.

Eventually, I found the issue. It was not the code. It was not the machine. It was not the setup sheet. It was definitely not the intern.


I had clamped the part upside down myself. No one knew but me, and that is how this story stayed."


– Machinist

Video of the Week (Powered by GibbsCAM)

This GibbsCAM Tech Tip teaches you how to use Combined Shapes to quickly add, subtract, intersect, trim, and slice geometry without manually trimming, untrimming, or reconnecting lines.

CAMedy Central

Industry Intel

Manufacturers Report Growth

Manufacturing stayed in expansion for the fourth straight month, but weaker backlogs, exports, and employment suggest growth is slowing and the recovery is becoming more cautious.


Updated Federal Guidance and Funds May Boost Manufacturing Apprenticeships

New federal guidance and a $35.8 million incentive fund could make it easier and more affordable for manufacturers to start or expand registered apprenticeship programs.


GM's US Manufacturing Investments Surpass $6B In One Year

GM plans to invest $830 million in Michigan and Ohio facilities to expand transmission and engine component production for next-generation trucks and SUVs, bringing its U.S. manufacturing investments to more than $6 billion over the past year.



Industry Growth (Open Jobs)

A few hot openings across the industry this week:



CNC Programmer - Dahlquist Machine - Ham Lake, MN


CNC Machinist - Dahlquist Machine - Ham Lake, MN


CNC Prototype Machinist - The Tory Company - Minneapolis, MN


CNC Programmer - Carver Pump Company - Muscatine, IA


Machinists (Nights/Sun-Tues) - Graco - Sioux Falls, SD


Machinist - Doosan Bobcat NA US - Wahpeton, ND


CNC Machinist - Speedway Motors Inc. - Lincoln, NE


CNC Machine Operator/Programmer - Lowell Manufacturing Company - Pacific, MO


Experienced CNC Machinist (2nd Shift) - Metal Arts Machine Co., LLC - Wichita, KS

Trade Show & Event Radar

Date

Show

Location

May 12-13

SteakFest 2026 Open House

Delafield, WI

June 22-25

Automate

Chicago, IL

July 29-30

Advanced Manufacturing Expo

Grand Rapids, MI

Sept 14-19

IMTS

Chicago, IL

Oct 6-7

Top Shops Conference

Cleveland, OH

Oct 21-23

FABTECH

Las Vegas, NV

November 11-13

Titans of CNC Boombastic Show

Flower Mound, TX

Did someone forward you this newsletter?

Subscribe to get your own copy every week.