Axial engine has ABC cylinder and liner construction- "A"luminum piston, "B"rass cylinder liner that is "C"hrome plated. Composite bodied 9.0mm 3-needle slide valve carburetor, factory reset line on High-Speed Needle and flush needles make resetting to factory specs easy, also includes 8.0 and 8.5mm venturis.

Key Features:

• Includes 3 distinctive rear exhaust headers
• Made from strong lightweight 6061 aluminum
• Fits most 1/10th scale sedan and gas trucks

This is the Hard Bodyz Tuber for the AX10 Warthog, Grey. The Warthog competition chassis is designed for serious crawling competition. Designed by Ryan Gerrish who competes at the highest level at national crawling events.

This is the piston and cylinder set for the Kyosho GXR-18 and GXR-18SP Engine. This is the 'B' version which has improvements over the original version. The GXR18 engine features a zero-Loss pull-starter; so once you start the engine, all of the power is getting to the ground – none of it is wasted on spinning parts that are only used to start the engine.

O.S. 21XM outboard marine engine has simple construction for easier maintenance translates to more time in the water, less time on the bench. Comes with pre-installed tiltable mount for adjustable "plane", and also comes with a carbon propeller.

This is the O.S. Max .21 VZ-M Turbo Marine Engine.

Key Features:

• Water intake mounted directly onto plug channels.
• ABC cylinder construction
• Rear exhaust

O.S. Max 30VG(P) Rear Exhaust Monster Truck Engine with Pilot Type Crankshaft.
Key Features:

• Same mounting dimensions as .21 size engines.
• Advanced Bi-Metallic Liner
• Machined aluminum piston, 3-port cylinder liner and double bushed knife edge connecting rod.

O.S Engine is designed specifically for this engine, this system guarantees the steady fuel supply, needed for the most-demanding of 3D flights with constant, vigorous attitude and throttle changes. The 91HZ-R also performs well as an F3C powerhouse providing a steady, smooth run and exacting mixture controls.

This is the O.S. Max FL-70 4-Stroke Model Airplane Engine. This FL-70 engine provides easier handling and maintenance, lighter weight and lower cost to 4-stroke newcomers and Sunday fliers. This engine is Approximately 20% lighter than the FS-70SII owing to a plastic cover plate, redesigned mechanism and smaller number of parts.

This is the RB Concept S3 II L2G Buggy Engine.
Key Features:

• Ideal for club racers and beginners.
• "ABC" cylinder & piston set
• Double rubber shielded front bearing.

This is the RB Products WS7 L2G Turbo Engine. This new engine has a lot of exclusive features, like the special RB Concept Coating, the new off Road Carburetor (including extra stiffer, anodized body and interior steel rings plus a 8mm Venturi).

RB Concept S7 L2G .21 cu in (3.49cc) Off-Road Engine. The L2G 11-fin orange colored aluminum cooling head lowers weight to improve vehicle's handling and increases cooling efficiency with fins concentrated around combustion chamber. Vacuum molded alloy crankcase.

This is the RB Products RB Concept WS7 Turbo Engine L2G Combo. This version of the WS7 Turbo comes with an exhaust system, consisting of a manifold and pipe. This engine has the L2G low profile head which increases cooling efficiency and comes with a new turbo combustion chamber.

This is the RB Products In-Line 2045P/192P Tuned Pipe Kit.
Key Features:

• Polished aluminum pipe construction.
• Inline design
• Length 6.88" Dameter 1.49"

In the world of 1/8 scale on-road racing there is one word that makes the difference between a consistent winner from those who simply show up to race… SETUP! The more precisely your car is “dialed” to the track the more likely you will have a checkered flag in your future.

This is the RD Logics .25 RTR Engine. This engine is nitro powered and comes with its carburetor factory preset- no adjusting required! RD Logics suggests using 5-15% Nitro Fuel with this engine.

This is the RD Logics Team Infinity Katana 512TB. This engine comes equipped with dual ball bearings, Schnuerle porting, ABC and mixture control carburetors. 

This is the RD Logics Aluminum Arms Set. This set is purple colored and for the HPI Baja 5b. Includes 1 front pair lower arms, 1 front pair upper arms, 1 rear pair lower arms, and 1 rear pair upper arms.