Issue 44

April 23, 2026

Time to Read: 6 minutes


-Hot Take-

“We’ve always done it this way” is just code for “We stopped caring about being competitive years ago.”

Joke of the Week

Q: What's the difference between "it ran fine last time" and useful information?

A: Useful information helps.

Ask a CAM Pro

Real shop problems. Answers from people who have been there.

How do I program parts for sub-spindle transfer?


Sub-spindle transfer is one of the highest risk moments in a turning cycle. You are moving a partially finished part between spindles, relying on synchronization, clamping, and offsets to be perfect. Small errors create big crashes. The goal is a repeatable handoff where both spindles agree on position, speed, and timing every time.


Start with clear work offsets for main and sub.

Set separate work offsets for each spindle and define exactly how Z-zero is established for both. Pick a reference method that is repeatable, probing, a known gauge point, or a controlled touch-off routine. If the spindles do not agree on Z, everything downstream will be wrong.


Plan the transfer sequence before you cut.

Define the order: orient, sync, approach, clamp, confirm, release, retract. Do not improvise the sequence inside the program. A consistent pattern reduces mistakes and makes prove-out faster.


Synchronize spindle speed and direction.

Bring both spindles to the same RPM and rotation direction before the pickup. Use the machine’s sync commands, then add a short dwell to allow stabilization. Verify the spindle direction, because the wrong direction during sync can twist or slip the part.


Control approach and pickup position.

Rapid close, feed slow. Use a safe rapid to a known clearance point, then a controlled feed move for the final pickup distance. Keep that final approach consistent and avoid “sneaking up” by hand editing Z values at the control, that is how transfer errors get repeated.


Clamp with timing and confirmation in mind.

Command the sub chuck close, then allow time for full clamping pressure. If your machine supports clamp confirmation or pressure checks, use them. Do not release the main spindle until you know the sub has the part.


Leave the right amount of stock for cutoff.

Do not part off with a fragile web that can tear, and do not leave so much stock that the cutoff loads spike. Reduce feed near breakout and keep coolant strong to prevent a torn face or pulled part during separation.


Protect the cutoff and transfer zone.

Make sure the cutoff tool fully retracts before any spindle retract or index. Use safe positions that clear jaws and workholding. Most transfer crashes happen in non-cutting motion, not during the cut.


Re-establish Z for second-op work.

After transfer, confirm the sub-spindle Z reference for finishing operations. If length matters, use a touch-off or probing step on the transferred part face to dial in the sub offset before finishing critical features.


Verify the full transfer in machine simulation and dry run.

Run the transfer with both spindles active and watch every command: open, close, sync, dwell, retract, and park moves. Then dry run above the part with overrides. Treat the first prove-out like a controlled test, not production.


Bottom line:

Sub-spindle transfer is about coordination and repeatability. Separate offsets, clean synchronization, controlled approach, confirmed clamping, and verified motion are what make the handoff safe and consistent.


Have a programming question?


Send it in for the next edition of Ask a CAM Pro!

Weekly Poll

Choose from the answers below.

(Keep scrolling to see last week's poll results.)

What causes more lost time than most shops admit?

View the results of last week's poll HERE.

From the Floor

We Saved the Lathe From 1986 (Barely)


"Some folks think old machines are dinosaurs, but I’ve been around long enough to know they don’t die easy. We’ve still got a lathe from ‘86 on the floor, bought new back in the day, and yes, it’s still (usually) running parts.


Sure, it’s down right now, waiting on some TLC, but it reminds me how many shop years get poured into these machines. Every time it spins up, there’s a weird sense of pride...like keeping a family car on the road for decades. It's a little piece of history, mixed in with the new."


– Manufacturing Engineer

Video of the Week (Powered by GibbsCAM)

GibbsCAM Milling from a Solid Tutorial Playlist

This four-part GibbsCAM mill tutorial playlist walks through the complete workflow of machining a part from a solid model, from importing and aligning the solid, to building the tool list, roughing the part, and finishing the features and holes. 

CAMedy Central

Industry Intel

Beer Giant Pours $600M into U.S. Production in Major Bet on American Growth - Anheuser-Busch says it will invest $600 million in its U.S. operations over two years to expand brewery capacity, add training centers, and strengthen workforce development, including veteran hiring initiatives.


The New Industrial Renaissance: How Smart Manufacturing Is Rewriting Heavy Industry - This article argues that heavy industry is being transformed by connected data, digital twins, and AI, but real results depend on strong data foundations, change management, cybersecurity, and clear implementation strategy.


Building a Bridge Between Education and Industry - This article highlights Sandvik Coromant’s nearly 20-year partnership with Canada’s Northern Alberta Institute of Technology, showing how investment in modern training, tooling, and hands-on education is helping close the machining skills gap and prepare students for today’s manufacturing workforce. 

Industry Growth (Open Jobs)

A few hot openings across the industry this week:



CNC Programmer/Machnist - Imagineering Machine Inc. - St. Louis Park, MN


U001 Tool and Die Maker - Northrop Grumman - Elk River, MN


CNC Machinist - Delva Tool & Machine - Paullina, IA


CNC Machinist - Kolberg-Pioneer Inc - Yankton, SD


Senior Programmer - Clearwater Custom Cabinets - Horace, ND


Tool Die Maker (2nd Shift) - Parker Hannifin Corporation - Kearney, NE


Lead CNC Mill Machinist/Programmer - E&E Machine - Moscow Mills, MO



CNC Programmer - Acro Corp - Wichita, KS

Trade Show & Event Radar

Date

Show

Location

May 5-6

Morris & Tsugami America Open House

Brooklyn Park, MN

May 6-7

TechDays 2026

Mebane, NC

May 12-13

SteakFest 2026 Open House

Delafield, WI

June 22-25

Automate

Chicago, IL

July 29-30

Advanced Manufacturing Expo

Grand Rapids, MI

Sept 14-19

IMTS

Chicago, IL

Oct 21-23

FABTECH

Las Vegas, NV

November 11-13

Titans of CNC Boombastic Show

Flower Mound, TX

Did someone forward you this newsletter?

Subscribe to get your own copy every week.