Issue 73

November 12, 2026

Time to Read: 7 minutes


-Hot Take-

A process that only exists in the owner’s head will break the minute someone else tries to grow the shop.

Joke of the Week

Q: Why do machinists make bad comedians?

A: Great material, late delivery.

Ask a CAM Pro

Real shop problems. Answers from people who have been there.

How do I document a setup for another programmer or operator?


A setup that only lives in your head is a setup only you can run. The first time you're out sick, on vacation, or buried in another job, someone else is going to stare at a vise, a stack of tools, and an NC file and try to piece it all together. Good setup documentation lets the next person load, run, and inspect the part without tracking you down, and it keeps every run of that job consistent.


Write for someone who has never seen the part.

Assume the reader is a capable machinist who knows nothing about this job. Skip the personal shorthand and spell out anything that took you a minute to figure out. If you had to think about it during prove-out, the next person will too.


Lead with workholding and part orientation.

Start with how the part is held. List the vise or fixture, jaw type and ID, parallel height, stop location, and clamping torque or pressure. Show which face is up and which edge goes against the stop. A screenshot of the part in the fixture from your CAM model, or a quick photo from the machine, beats a paragraph of description every time.


Define every work offset clearly.

Note which work offset each operation uses, exactly where zero is, and how to pick it up. Top of part and center of bore is clear. Zero on the part is not. If a probing routine sets the offset, list the program name or number. Mark up an image with the X, Y, and Z directions so nobody has to guess which way is positive.


Build a complete tool list.

Include tool number, description, diameter, corner radius, flute count, holder, length and diameter offset numbers, and insert grade where it applies. Call out minimum and maximum stickout, especially when holder clearance was verified at a specific length. A note like "1.25 minimum inch stickout" can save a holder from meeting a jaw.


Record the program details.

List the program name or number, revision, date, machine, and post used, along with approximate cycle time for each operation. Explain any optional stops or block skips and what they do. If a block skip turns on a second finish pass, say so.


Call out the risky moments.

Flag tight clearances, tools that run close to jaws or clamps, thin walls that need a reduced feed override, and anything that surprised you during prove-out. A short "watch this" section tells the operator exactly where to keep a hand near feed hold on the first part.


Add inspection and adjustment notes.

Identify the critical dimensions, the gauges needed to check them, and how often to check. Most importantly, note which tool and wear offset controls each critical dimension. Include adjustment instructions specific to the machine and operation, since the correct direction depends on the offset convention and machining strategy. That detail helps operators make the right adjustment without guessing or tracking down the programmer.


Let your CAM system do the heavy lifting.

Most CAM systems can generate setup sheets using information from the CAM program, including tool lists, offsets, stock size, and part images. Customize the template to match your shop's standard so every job looks the same and nothing gets retyped. Generate the setup sheet from the approved CAM file, and update it whenever the program or setup changes to make sure the documentation matches what's running on the machine.


Keep it in one place and keep it current.

Store the setup documentation with the program files under the same revision control. When an operator changes a stickout or adds a clamp, capture it and update the sheet. An outdated setup sheet can be worse than none at all because people trust it.


Bottom line:

Good setup documentation answers questions before anyone has to ask them. If the next programmer or operator can load, run, and inspect the part without hunting you down, you've done it right.


Have a programming question?


Submit your questions here anonymously!

Shop Floor Debate

Which CNC role gets the LEAST recognition for the work they do?

Last week's debate: There was a two-way tie for what causes the most emotional damage. See which situations tied!

From the IMTS Floor

AI Meets CAM Programming


What happens when AI starts making machining decisions alongside CNC programmers?


At IMTS 2026, Jessica caught up with David Priev, co-founder and CEO of Limitless Labs, to learn how his team is bringing AI into CAM programming.


Their AI agent is designed to understand CAD geometry, machining strategies, and manufacturing requirements, helping programmers generate toolpaths, explore different approaches, and work more efficiently within existing CAM software. But what does that mean for the people doing the programming? And how much decision-making should we hand over to AI?



David shares what the technology can do today, where it's headed, and why experienced machinists and programmers remain essential.

CNC Underground: Afterhours Podcast

Can AI Save Time AND Make Shops More Profitable?


What can AI actually do for a manufacturing shop today, and does saving time always translate into more profit? Chris Stevens, The Mfg Coach, joins CNC Underground: Afterhours to discuss how manufacturers are putting AI to work, where the real opportunities are, and why understanding your own processes matters more than chasing the latest technology.


Key Takeaways:

  • Why context matters more than cost when implementing AI in manufacturing.
  • Practical ways AI can save hours on everyday tasks, from emails to work instructions.
  • How small and mid-sized shops can use AI to their advantage without massive investments.


Is your shop ready to put AI to work? Hear what Chris has to say.

Video of the Week (Powered by GibbsCAM)

Operator | GibbsCAM 2027 Highlights

See how GibbsCAM GO Operator lets shop floor personnel adjust feeds and speeds, generate NC code, and prepare programs for production without a full GibbsCAM programming license.

CAMedy Central

Industry Intel

IMTS Drives Manufacturing Technology Orders Past $1B in September 2026

Boosted by IMTS, U.S. manufacturing technology orders hit a record $1,007.3 million in September 2026, up 38.0% from August and 101.7% from September 2025, bringing the year-to-date total to $5.76 billion, 45.0% ahead of 2025.


Robot Demand Surges as Manufacturing Expands

A3’s tally for North America shows 10,989 robots worth $723.5 million ordered in Q3 2026, with units up 22.9% from Q2 and 24.8% from Q3 2025, which puts the January–September total at 28,984 robots valued near $1.89 billion.


Here’s Where Engineering Talent Shortages Are Hitting Hardest

Recruiters tell Design News that the engineering shortage is most acute in aerospace and defense, data centers and power infrastructure, advanced manufacturing and automation, and reshored production, where order backlogs and new facilities are growing faster than qualified engineers can be hired.

Industry Growth (Open Jobs)

A few hot openings across the industry this week:


Swiss Programmer - Nelson Numeric - Minneapolis, MN


Haas Technical Trainer & CNC Programmer - Productivity Inc - Plymouth, MN


CNC Machinist III - Reell Precision Manufacturing - St. Paul, MN


CNC Programmer - Konrad Corporation - Hudson, WI


Machinist - Sekisui Aerospace - Orange City, IA


CNC Programmer - Terex Corporation - Huron, SD


CNC Programmer/Operator - Fargo Glass & Paint - Minot, ND


Die & Tool Maker - Dutton-Lainson Company - Hastings, NE



5-Axis CNC Machinist & Programmer - Mittler Bros. Machine & Tool - Wright City, MO


Production CNC Machinist (2nd Shift) - D-J Engineering, Inc. - Augusta, KS

Trade Show & Event Radar

Date

Event

Location

Feb 9-11

MD&M West

Anaheim, CA

Feb 22-24

Midwest Manufacturers Trade Show & Conference

Branson, MO

April 12-15

Machining Summit

Mammoth Lakes, CA

May 4-6

Precision Machining Technology Show (PMTS)

Cleveland, OH

May 10-13

Automate

Las Vegas, NV

May 19-20

MD&M East

New York, NY

Did someone forward you this newsletter?

Subscribe to get your own copy every week.