January 29, 2026

Time to Read: 7 Minutes


-Hot Take-

If you're still hand-programming your Swiss parts in 2026, you're leaving profit on the table and pretending it's tradition.

Joke of the Week

Q: Why did the part fail?

A: Because the quote didn't include reality.

Ask a CAM Pro

How do I program a 3d contour with smooth surface finishes?

3D contouring is where your CAM strategy really shows its skill. When you’re sculpting complex surfaces, molds, dies, turbine blades, or organic forms, surface finish is the difference between a clean shine and hours of hand polishing. Smooth results come from stable engagement, consistent stepovers, and proper tool control.


Start with the right tool and setup.

Use a sharp, balanced ball end mill or tapered ball cutter suited for the material. Keep stickout short and holder clearance verified. If possible, use a tool with a smaller radius or taper for fine detail. Any deflection or vibration here will show up as ripples on the part.


Use the right toolpath strategy for the geometry.

For flowing surfaces, go with constant step-over or morph between curves to maintain even cusp height. For steeper geometry, switch to steep-and-shallow or parallel-to-surface strategies. Avoid basic raster paths, they leave uneven marks where the tool engagement changes.


Control cusp height, not just step-over.

Cusp height determines the visual smoothness of the finish. Smaller stepovers reduce cusps, but they also increase cycle time. Use your CAM’s cusp control setting to find the balance, tight enough to eliminate visible scallops, loose enough to keep cutting time reasonable.


Keep feed and speed consistent.

A smooth surface comes from constant chip load. Sudden feed changes or deceleration points will leave marks. Use smoothing or look-ahead options in your CAM software to prevent jerky motion. Maintain feedrates through direction changes with arc fitting or motion filtering.


Finish with climb cutting where possible.

Climb milling cuts cleaner and reduces tool pressure. For 3D work, that means running toolpaths that allow the cutter to enter the surface gently and exit cleanly. Avoid conventional passes unless geometry forces it.


Maintain consistent tool engagement angles.

Program entry and exit arcs to avoid plunges. Keep the tool cutting with the side of the ball, not the tip, since the center of a ball end mill has near-zero surface speed. A small tilt angle or lead/lean adjustment helps keep cutting speed consistent and eliminates dead-center marks.


Use a dedicated finishing pass.

Never finish with a worn rougher. Always reserve a fresh tool for your final pass. Remove a light amount of material, around 0.003 to 0.005 inches, and run a constant tool load. If you skip semi-finishing, your finish pass will chase uneven stock and ruin the surface.


Simulate and verify your surface transitions.

Run the final toolpath in high-resolution simulation to check for abrupt direction changes or hidden retractions. Pay close attention to boundary conditions and where toolpaths end, an unwanted retract can leave a visible step.


Bottom line:

A smooth 3D surface isn’t about perfection in the tool, it’s about consistency in motion. Even engagement, clean entries, and steady feeds turn complex contours into mirror finishes.


Have a programming question?


Send it in for the next edition of Ask a CAM Pro!

Weekly Poll

Choose from the answers below.

(Keep scrolling to see last week's poll results.)

How much hand programming or manual G-code editing happens in your shop?

View the results of last week's poll HERE.

From the Floor

The Button No One Touches


"There’s a button on every CNC that nobody, and I mean nobody, wants to press. Ask anyone what it does, and half will say “don’t know, don’t care,” and the rest will tell you it’s always been that way.


One new guy asked me why we don’t try it. I told him, 'You can, if you like surprises.'


He didn’t.


It’s still there, untouched, like a dare."


-Machinist

Tech Tip (Powered by GibbsCAM)

Tech Tip: Eliptical & Interpolated Turning

This tech tip walks through how to create elliptical turning operations on a Y-axis lathe and interpolated turning on a mill in GibbsCAM. You’ll learn when to use each strategy, how to set them up, and what machine requirements to watch for.

CAMedy Central

Industry Intel

John Deere Announces Major Expansion with Two New U.S. Facilities Coming - John Deere is expanding U.S. manufacturing by opening a new Indiana distribution center and a North Carolina excavator factory, creating hundreds of American jobs and bringing excavator production back from overseas to the United States.



XTJ CNC Provides State-of-the-Art Precision CNC Machining for Critical Industries - XTJ CNC is an Indiana-based precision machining company providing high-tolerance CNC milling, turning, and rapid prototyping services for critical industries like aerospace, automotive, and electronics, supporting projects from early prototypes through production.


Global CNC Machine Market to Nearly Double by 2032, Forecast to Approach USD 196.1 Billion - The global CNC machine market is projected to nearly double by 2032, driven by automation, Industry 4.0, AI integration, sustainability goals, and rising demand for high-precision manufacturing across major industries.

Industry Growth (Open Jobs)

A few hot openings across the industry this week:



Machinist III (PT/Weekends) - Collins Aerospace - Burnsville, MN


CNC Machinist - Tesla - Brooklyn Park, MN


CNC Manufacturing Engineer (Level II) - Advance Machine Technologies - Johnston, IA


CNC Machinist (Aerospace & Defense) - Rensberger Technologies Inc - Sioux Falls, SD


Fabrication Machine Operator - Doosan Bobcat - Bismarck, ND


Manufacturing Engineer (CNC Machining) - Kinney Manufacturing, LLC - Lincoln, NE


CNC Programmer Trainee - Patriot Machine Inc - St. Charles, MO


CNC Machinist - Boeing - Wichita, KS

Trade Show & Event Radar

Date

Show

Location

Feb 3-5, 2026

MD&M West

Anaheim, CA

Feb 23-25

Midwest Manufacturers Trade Show & Conference

Branson, MO

April 8-9

2MTEC

Albert Lea, MN

April 13-16

Machining Summit on the Summit

Mammoth Lakes, CA

April 13-16

Modex26

Atlanta, GA

April 22-23, 2026

MD&M South

Charlotte, NC

June 22-25

Automate

Chicago, IL

Sept 14-19, 2026

IMTS

Chicago, IL

Did someone forward you this newsletter?

Subscribe to get your own copy every week.